Pipe offset calculator

Two elbows move the line over by the offset. Enter the offset and the angle or the run; the cut length takes off both elbows and a weld gap at each end.

What you know besides the offset
Units
6" · BW LR · gap 1/8"
Elbows

Butt-weld elbows from the chart: a long-radius 45 at 45°, otherwise a 90 cut to the angle. For socket-weld, threaded or a fitting you measured, choose My takeout.

33-15/16" Offset 24" Run 24" 45.00°
Cut length 26-3/16"
Travel
33-15/16"
Run
24"
Angle
45.00°
Takeout, each
3-3/4"
ASME B16.9 · 3 catalogs
Steps
  1. Travel = 24 × 1.4142 = 33.941"
  2. Run = 24 × 1.0000 = 24"
  3. Takeout = 3.75" eachASME B16.9 · 3 catalogs
  4. Cut = 33.941 − 2 × 3.75 − 2 × 0.125 = 26.191" → 26-3/16"

Verify critical dimensions against the current standard before fabrication.

A worked example

A 10" offset with a 12" run, on 6" pipe with long-radius 90s cut to the angle, and no gap. This one is from the worked examples in a handheld pipe calculator's published guide; the calculator here gives the same answers.

  1. Travel = √(10² + 12²) = 15.62"
  2. Angle = atan(offset ÷ run) = atan(10 ÷ 12) = 39.81°
  3. Takeout = R × tan(θ/2) = 9 × 0.3620 = 3.258" eachR: ASME B16.9 · 3 catalogs
  4. Cut = 15.62 − 2 × 3.258 = 9.104" → 9-1/8"

Before cutting each 90 to the angle, mark it along the inside 3-15/16", centerline 6-1/4", outside 8-9/16".

Cut the pipe to 9-1/8".

The same idea in millimeters

A 600 mm offset at 45°, DN 150 long-radius 45s, a 3 mm gap:

  1. Travel = 600 × 1.4142 = 848.5 mm
  2. Run = 600 × 1.0000 = 600 mm
  3. Takeout = 95.3 mm eachASME B16.9 · 3 catalogs
  4. Cut = 848.5 − 2 × 95.3 − 2 × 3 = 652 mm

The formulas

  • Travel = offset ÷ sin θ and run = offset ÷ tan θ, θ being the fitting angle.
  • With the run known instead: travel = √(offset² + run²) and θ = atan(offset ÷ run).
  • Cut = travel − 2 × takeout − 2 × gap for butt welds: one takeout and one root gap at each end.
  • A 90 cut to θ: takeout = A × tan(θ/2), where A is the 90's center to end.
Multipliers for common fitting angles
AngleTravel = offset ×Run = offset ×Takeout of a 90 cut to it = A ×
5-5/8°10.202310.15320.0491
11-1/4°5.12585.02730.0985
22-1/2°2.61312.41420.1989
30°2.00001.73210.2679
45°1.41421.00000.4142
60°1.15470.57740.5774

Questions

Travel or cut length?

Travel is center to center between the two elbows. The cut length is the pipe you cut: the travel less both takeouts and a gap at each weld.

Which takeout does it use?

For long-radius elbows at 45°, the stock 45 from the elbow takeout chart. At any other angle, a 90 cut to the angle: A × tan(θ/2). Short-radius elbows don't come as stock 45s in the chart, so they're cut from a 90 too. For socket-weld, threaded, or a fitting you measured, open the pipe bar and choose My takeout.

Why two gaps?

The pipe has a weld at each end, and each weld has its own root gap. Set the gap to 0 for a fitting with no gap.

It says there's no pipe left to cut

The two elbows and gaps take up more than the travel. A bigger offset or a smaller angle gives a longer travel; a shorter fitting gives more pipe.

Can I work in metric?

Switch to mm. What you've typed converts, so 1/8" becomes 3.2 mm instead of resetting.

Where the takeouts come from

Elbow center-to-end values are ASME B16.9 dimensions that agree in at least two of these catalogs:

Pipe outside diameters, used for the cut marks:

Verify critical dimensions against the current standard before fabrication.

Keep it in your pocket

The app does this offline, saves it to a job and prints a cut sheet, and adds rolling offsets, laterals, miters, saddles and the fitting tables. $19.99 once, no subscription.

Coming soon to the App Store$19.99 once · iPhone and iPad

What's in the app

Spoolhand on iPhone: a simple offset of 24 inches at 45 degrees on 6-inch long-radius 45s, cut length 26-3/16 inches.