Rolling offset calculator

The set and the roll move the line up and over at once. Enter both, plus the angle, the run or the travel.

What you know besides the set and roll
Units
6" · BW LR · gap 1/8"
Elbows

Butt-weld elbows from the chart: a long-radius 45 at 45°, otherwise a 90 cut to the angle. For socket-weld, threaded or a fitting you measured, choose My takeout.

38-5/8" Run 27-5/16" Set 24" Roll 13"
Cut length 30-7/8"
True offset
27-5/16"
Travel
38-5/8"
Run
27-5/16"
Angle
45.00°
Takeout, each
3-3/4"
ASME B16.9 · 3 catalogs
Steps
  1. True offset = √(24² + 13²) = 27.295"
  2. Travel = 27.295 × 1.4142 = 38.601"
  3. Run = 27.295 × 1.0000 = 27.295"
  4. Takeout = 3.75" eachASME B16.9 · 3 catalogs
  5. Cut = 38.601 − 2 × 3.75 − 2 × 0.125 = 30.851" → 30-7/8"

Verify critical dimensions against the current standard before fabrication.

A worked example

A 24" set and a 13" roll with a 32" run, on 6" pipe with long-radius 90s cut to the angle and a 3/32" gap. This one is from a handheld pipe calculator's published guide; the calculator here gives the same answers.

  1. True offset = √(24² + 13²) = 27.295"
  2. Travel = √(27.295² + 32²) = 42.059"
  3. Angle = atan(true offset ÷ run) = atan(27.295 ÷ 32) = 40.46°
  4. Takeout = R × tan(θ/2) = 9 × 0.3686 = 3.317" eachR: ASME B16.9 · 3 catalogs
  5. Cut = 42.059 − 2 × 3.317 − 2 × 0.094 = 35.238" → 35-1/4"

Before cutting each 90 to the angle, mark it along the inside 4", centerline 6-3/8", outside 8-11/16".

Cut the pipe to 35-1/4".

The same idea in millimeters

A 600 mm set and a 300 mm roll at 45°, DN 150 long-radius 45s, a 3 mm gap:

  1. True offset = √(600² + 300²) = 670.8 mm
  2. Travel = 670.8 × 1.4142 = 948.7 mm
  3. Run = 670.8 × 1.0000 = 670.8 mm
  4. Takeout = 95.3 mm eachASME B16.9 · 3 catalogs
  5. Cut = 948.7 − 2 × 95.3 − 2 × 3 = 752.2 mm

The formulas

  • True offset = √(set² + roll²): the diagonal of the set and the roll.
  • With the angle: travel = true offset ÷ sin θ, run = true offset ÷ tan θ.
  • With the run: travel = √(true offset² + run²), θ = atan(true offset ÷ run).
  • With the travel: run = √(travel² − true offset²).
  • Cut = travel − 2 × takeout − 2 × gap for butt welds.
Multipliers for common fitting angles
AngleTravel = offset ×Run = offset ×Takeout of a 90 cut to it = A ×
5-5/8°10.202310.15320.0491
11-1/4°5.12585.02730.0985
22-1/2°2.61312.41420.1989
30°2.00001.73210.2679
45°1.41421.00000.4142
60°1.15470.57740.5774

Questions

Set or roll?

They're the two sides of the move, measured center to center: the set is usually the vertical one and the roll the horizontal one. Swapping them gives the same true offset, travel and cut.

What's the true offset?

The straight-line distance the pipe really moves, square to the run. Once you have it, a rolling offset works like a simple offset.

Which takeout does it use?

For long-radius elbows at 45°, the stock 45 from the elbow takeout chart; at any other angle, a 90 cut to the angle: A × tan(θ/2). For socket-weld, threaded, or a fitting you measured, choose My takeout.

The travel is too short

When you give the travel, it has to be longer than the true offset; otherwise there's no run that fits.

Where the takeouts come from

Elbow center-to-end values are ASME B16.9 dimensions that agree in at least two of these catalogs:

Pipe outside diameters, used for the cut marks:

Verify critical dimensions against the current standard before fabrication.

Keep it in your pocket

The app does this offline, saves it to a job and prints a cut sheet, and adds parallel offsets, laterals, miters, saddles and the fitting tables. $19.99 once, no subscription.

Coming soon to the App Store$19.99 once · iPhone and iPad

What's in the app

Spoolhand on iPhone: a simple offset of 24 inches at 45 degrees on 6-inch long-radius 45s, cut length 26-3/16 inches.